Injection Technique

[bigrand]

Hey bros,

Curious, what is your procedure for injecting? Is it something like whats on 2Thicks site? Also, does anyone have any good pics of where to inject on the quad? Im about to give my first inject with a 21G, 1-1/4 (got them for free), and wanna make sure in doin EVERYTHING right.....

 

[ryker77]

1 wash your hands and area for injection (turn AC on, lock door)
2 wipe hands off with alchol pad
3 wipe vial stopper off with a new alchol pad
4 take a 18-22 gauge pin and pull plunger
5 insert pin into vial
6 turn vial upside down
7 inject the positive amount of air
8 pull out amount of oil
9 push oil back in till you get what you want
10 turn vial right side up and pull out pin
11 wipe the stopper off again
12 pull plunger down to 3ml
13 let oil run down ( if useing a small pin then heat sryinge)
14 take off the dull pin
15 put on a new pin
15 push plunger up till no air is left and just a tad of oil runs out of the pin
16 wipe injection area with alchol pad
17 let area dry ( hurts like hell if you don't)
18 think about how much you spent on the gear
19 lie down keep head lower than your body to keep blood in your brain ( to keep from passing out )
20 find correct injection area
21 put pin on skin and push till you break the skin
22 keep pushing till pin stops
23 aspirate (only if you won't pass out)
24 inject slowly
25 pull pin out wipe area again with alchol wipe

 

[bigrand]

THANKs for the list bro, ima print it

I bet ill still get hella nervous and have an anxiety attack, so ill keep #19 in mind. Im glad you added in #18 too, its very important.......lol

 

[tarzan21]

youll be fine bro

 

[Thaibox]

18 think about how much you spent on the gear

 

[Daeo]

21G in the quad. Ouch I use 23G and I still hate it. It's not that bad though, just a bit uncomfortable...

 

[bigrand]

Daeo, thanx for those words of encouragement! Its all i got and i cant see what im doin if i put it in my ass, so thats why i wanna put it in the quad. I wanted 23g, but my potna gave me 21g pins for free. Maybe ill wait until i can get some 23g...........
Itl probly hurt so bad i wont be able to tell if its just the injection or an infection!

 

[sausage]

ive only done 1 cycle and every shot was in my glute trust me its a lot easier than you think after the first shot you wont be nervous.

 

[Daeo]

Daeo, thanx for those words of encouragement! Its all i got and i cant see what im doin if i put it in my ass, so thats why i wanna put it in the quad. I wanted 23g, but my potna gave me 21g pins for free. Maybe ill wait until i can get some 23g...........
Itl probly hurt so bad i wont be able to tell if its just the injection or an infection!

Sorry brother. I hate it just as much as you probably will(leg injections that is). These days 23G is the largest thing I'll voluntarily stick into any part of my body. I'd buy some pins if I were you. They only cost around $20. It's worth it...

 

[Jeff_rys]

There is no need for a 23 gauge for ANY roid

21G in the quad. Ouch I use 23G and I still hate it. It's not that bad though, just a bit uncomfortable...

Daeo, you should use a 25 g for any roid exept Winny-V. But 23 is too thick for Winny-V also, so although Dan Duchaine said to use a 23 g, in my book a 23 g is a total waste of gauge number to use.

Most oils will go through a 26, some through a 27 after heating the syringe.

 

[jstrong20]

Damn! Thats alot more steps than I use. Also why would you turn on the ac and why would anybody passout, just curious.

 

[testalot]

986

pass out = hit a vein

 

[Jeff_rys]

Re: 986

pass out = hit a vein

shouldn't it be "911"

 

[Daeo]

Re: There is no need for a 23 gauge for ANY roid

Daeo, you should use a 25 g for any roid exept Winny-V. But 23 is too thick for Winny-V also, so although Dan Duchaine said to use a 23 g, in my book a 23 g is a total waste of gauge number to use.

Most oils will go through a 26, some through a 27 after heating the syringe.

My girlfriend(the one who does the majority of my injections)and I don't have the sort of patience it takes to inject from a 25-27G I can live with using a 23G needle. Also, I had a hell of a time getting the Ttokkyo winny to flow through a 23G much less a 25G needle...

 

[Jeff_rys]

Re: Re: There is no need for a 23 gauge for ANY roid

My girlfriend(the one who does the majority of my injections)and I don't have the sort of patience it takes to inject from a 25-27G I can live with using a 23G needle. Also, I had a hell of a time getting the Ttokkyo winny to flow through a 23G much less a 25G needle...

that's what i said: Winny-V is the exeption. I use a 30 gauge for the Zambons, so you see the difference.
The advantage from a thinner needle: you have to pace the injection because you cannot shoot the gear in fast. So? Less change for an absess....
But i understand that your girlfriend has not the force. On the other hand, no one does my injections for me, i do them myself. If it goes wrong, it was my mistake.

 

[bigrand]

I guess i can wait until i find some 25G needles. The 21G is a big fucker.

 

[ryker77]

Damn! Thats alot more steps than I use. Also why would you turn on the ac and why would anybody passout, just curious.

The A/C is to help with those who have a problem injecting. If thier hot then they'll get frustrated. Also for hygine if your hot and nervous then you'll be sweating- which isn't good.

Passing out. Some people have a hrad time dealing with blood or needles.