Please Scroll Down to See Forums Below
napsgear
genezapharmateuticals
domestic-supply
puritysourcelabs
UGL OZ
UGFREAK
napsgeargenezapharmateuticals domestic-supplypuritysourcelabsUGL OZUGFREAK

Injection and needle size question.

richspc

New member
I want to spot inject into the quads. I have andropen275, oil base. Thinking of drawing with a 22G needle and syringe, then switching needle to a 25g to then run into the quad. My question, Can I run the oil base andropen in a 25g needle without any problems. I would appreciate your input, because I have to place the order. Thanks-bros.
 
richspc said:
I want to spot inject into the quads. I have andropen275, oil base. Thinking of drawing with a 22G needle and syringe, then switching needle to a 25g to then run into the quad. My question, Can I run the oil base andropen in a 25g needle without any problems. I would appreciate your input, because I have to place the order. Thanks-bros.
yes 25 gauge is no problem.....check out spotinjections.com and read everything...its very helpful
 
Prob. could but it would take a while. What about 23g? It's not that much dif. to me. Once you get past the initial skin prick, I can't tell the dif.
 
richspc said:
I want to spot inject into the quads. I have andropen275, oil base. Thinking of drawing with a 22G needle and syringe, then switching needle to a 25g to then run into the quad. My question, Can I run the oil base andropen in a 25g needle without any problems. I would appreciate your input, because I have to place the order. Thanks-bros.

youll be fine bro....25g 1 inch in quad is no problem, only thing i would suggest is run that loaded syringe under hot water for a min or 2 prior to shooting to improve the viscosity making it easier on you to depress the plunger requiring alot less pressure........goodluck
 
boops said:
youll be fine bro....25g 1 inch in quad is no problem, only thing i would suggest is run that loaded syringe under hot water for a min or 2 prior to shooting to improve the viscosity making it easier on you to depress the plunger requiring alot less pressure........goodluck

good tip, I always feared pressing down too hard and injecting too fast, because it really does take a bit of pressure for me to do delt shots, but slow and steady always does the trick
 
boops said:
youll be fine bro....25g 1 inch in quad is no problem, only thing i would suggest is run that loaded syringe under hot water for a min or 2 prior to shooting to improve the viscosity making it easier on you to depress the plunger requiring alot less pressure........goodluck

Be sure to keep the needle capped!! Tap water has all kinds of nasties in it. I prefer to heat up the vial in a baggie under hot water before injection. Works just as well without the chance of contamination from the water.
 
anal itch said:
Be sure to keep the needle capped!! Tap water has all kinds of nasties in it. I prefer to heat up the vial in a baggie under hot water before injection. Works just as well without the chance of contamination from the water.


ehh i guess i should never assume one would be smart enough to know better then to do anything other then draw and shoot with the cap on the needle...thank you for the addition
 
anal itch said:
Be sure to keep the needle capped!! Tap water has all kinds of nasties in it. I prefer to heat up the vial in a baggie under hot water before injection. Works just as well without the chance of contamination from the water.

Actually a heating pad works better than the water...at least that is my opinion as it gets it much warmer and more fluid. With the dart capped as mentioned and your gear in the syringe, just wrap it in the heating pad and go take a hot shower. I would then get out about 5 minutes later with a clean hot butt (insert obvious joke here) and rub a little alcohol on my adorable posterior and stick the dart in. NO pain, like a knife thru butta and I feel it helps the oil spread out easier when so warm.

I tried everything and this was by far the best. Or you could just suck it up and jab it in you nancy. :)
 
and to answer your initial question, I would use a 23 for both. It makes it easier to draw and the stick is not bad at all. You can use a 25 but as stated it will take a little longer to draw. No worries if you have the time. Good luck bro.
 
asianlover said:
you can use 25g. 23g would be much quicker though.

yes and over time cause more scar tissue but i guess it all comes down to personal preference...for what we do id rather not rush anyway....25 all the way or higher (higher meaning smaller needle)....
 
yes and over time cause more scar tissue but i guess it all comes down to personal preference...for what we do id rather not rush anyway....25 all the way or higher (higher meaning smaller needle)....


I'd like to see you draw some deca w/ a dart smaller than 25g. You'll be here next wk. still drawing.
 
cranny said:
I'd like to see you draw some deca w/ a dart smaller than 25g. You'll be here next wk. still drawing.


well since my statement said about causing scar tissue it had absolutely nothing to do with drawing, personally i draw with an 18g then SWITCH to the smallest guage possible (25,27, or slin) :)
 
drawing with the same needle makes it dull as hell and that hurts. nothing better than a sharp needle, goes in easy. be careful not to have the needle too loose on the syrainge cause it will unlatch and spray everything within a 2 feet radius with oil. happened to me once. and my room smelled like test for a week.
 
man I can always count on someone asking the questions I want the answers to if I just look around. Im getting ready to go with 400mgs test cyp (2 injections a wk) next week, I chose to draw with 20g and inject with 25g 1in. (in the quads) Looks like I made the right decision after my research. As always, tons of good info on here!
 
Top Bottom