In the process of making fina...please help

[RRR]

First time fina maker here, so I have a few questions and I'm sure in about an hour I'll have another few questions. I just want to make sure I got this right. Here are my questions:

1)I touched the pellets with my hands to put them in a straw, is that going to make it unsterile, if so after the whole process it should make it sterile right?
2) how long should I leave the pellets in the solution for after they have been crushed?

thanks

 

[OKIE]

Touching them will not harm them as long as you utililize the sterilization filter process later. Leave the pellets in the solution until they are completely dissolved.

 

[Torch]

Check it out

http://www.gotfina.com/articles/make.html

 

[FOZY]

I just made it this past weekend...yook my first shot on Sun and due up again tonight (100mg eod)

If you put the straw at the end of the little cart holes and tip it upside down they slide right in....so much esasier then picking them up.......2 carts I used 2 straws, just have to mash them up every once in a while

 

[RRR]

alright, its been 2 1/2 hours since the crushed pellets have been sitting in the magic solution. I see the tren on the top, but there seems to be still some pellets left at the bottom, or is that just the glue? how do you know for sure its ready for the next step which is adding the oil?

I know these might seem like stupid questions, but again I want to make sure this is coming out right.

 

[Torch]

heat the soloution on low and swirl it around til all the pellets dissolve. Do not add the oil til all is dissolved.

 

[RRR]

OK here's the update: I let the fina sit over night - 20hours - and there was still some pellets on the bottom, so i boiled some water and let it sit in there for 15 min, swirling it around. It dissolved most of the pellets but there were still about 4 small white pieces I could see at the bottom so i reboiled the water and put it back for another 5 min.......no change. Is this normal? should i let it sit for awhile, or try boiling it again, or is it normal?

 

[OKIE]

I think it is common to have a few small pieces left. I don't think I got mine 100% dissolved either. I would just go ahead w/ the rest of the process. I think the only way to get them completely dissolved is to crush them up really well beforehand.

 

[hockey1]

i converted minr this weekend for the first time,i nuked my crushed pelletes in the majic solution and it was good in 10 minutes,did have a few tiny particles left,i then poured it into vial 2 minus 11cc of oil.After i did that i shook it up then let it sit in boiling hot water for 15 mimutes,it took about 20 minutes to seperate,after it seperated i drew it out and injected it into a sterile vial using the micron filter and it is working fine and does not hurt when shooting.

 

[RRR]

I ran into a problem last night, I drew out 2cc of oil in a needle and dumped the rest of the oil in the fina bottle, i filled it all the way to the top but there was some oil left in the bottle, I couldn't fit all the oil in. I let it set overnight and the gunk is on the bottom, the fina is on the top but now what should i do about the extra oil? The kit is from finakits.com.

 

[RRR]

bump

 

[OKIE]

Don't worry about the extra oil. Just throw it away. They give you more than you actually need.

 

[RRR]

me again, I didn't think I would run into so many problems making this. Here is my next question:
After letting the tren sit in the bottle with oil it has 3 different colors. The bottom part with the glue and all the other shit has 2 different layers of color, 1 is a very small layer with a whitish color on the bottom part. And on the top of that is a dark brownish color and the rest is the fina, is this normal? Also what should I do with the extra 2cc of oil in the syringe.....junk it? Thanks guys I really appreciate the help.

 

[RRR]

I'm going to have to bump this. I know I'm being a pain in the a-- but if you could help me out please. Thanx

 

[OKIE]

me again, I didn't think I would run into so many problems making this. Here is my next question:
After letting the tren sit in the bottle with oil it has 3 different colors. The bottom part with the glue and all the other shit has 2 different layers of color, 1 is a very small layer with a whitish color on the bottom part. And on the top of that is a dark brownish color and the rest is the fina, is this normal? Also what should I do with the extra 2cc of oil in the syringe.....junk it? Thanks guys I really appreciate the help.

Yes, this is normal before the filtering process. The 2ccs in the syringe are for pushing any extra tren through the WhatMan Sterile Filter. Anything more than that is just trash.

 

[RRR]

Its finally done!!! I ended up putting the vial in water for 20 min 2X's and it seemed like it helped it, it put more color on the top. So I put it through the filter and let her go...........the end result a fine looking yellow color just like the one in the picture under articles. I know there had to be some fina in the gunk but I think the boiling today helped remove probably around 70% of what was at the bottom. So anyway its baking right now and in about 1 hour its time to GROW!!!
Thanks to everyone who helped me out, I appreciate it!