If it isn't BA, what is it?

[MrRTTB]

Tried the BA remove with Dest water but it didn't work for this gear I have, test prop. I have used the metiod before with success so I guess there are no BA but maybe something else. Q, what could there be in this test prop of mine that makes pain like BA but dest water will not attach to it like with BA (dest water + BA = the dest water will draw the BA out from the gear..)

Anyone have an idea?

The propionate muist have been suspended in something. And yes it's underground.

 

[40butpumpin]

I've only heard of oil, water or alcohol.

 

[ironmaster]

Benzl benzoate likely IS the problem. BB is commonly used in oil kits, fina kits, and by home labs to aid in suspending and preserving the solution. BB is some nasty shit......."for external use only, kills lice and scabies, should not be applied near open sores." It causes injection pain and flu like symptoms if present in high enough concentrations.
Tell me more about your technique for removing BA. I've never seen a consensus on how to do this. And I'd really like to know how to neutralize BB.......other than just buying euro gear.

 

[40butpumpin]

I've only heard of oil, water or alcohol.

Apologies to you bro for this response, I didn't read your post well enough.

 

[MrRTTB]

Ok, the method I have been using before to remove BA goes like this:

Í draw up 1cc gear into a syringe and after that draw up sterile water 0.5cc. This is my first try and If it's not enough I go with 50% of each (1ml gear and 1ml water). I then shake the syringe for 1 minute and then let it sit over night with pin DOWN. In the morning there are 2 layers, at the bottom water/BA and at the top "gear with less or no BA". I then Press out the bottom layer, change pin and warm again and then inject. This has worked very fine bofore with gear from chinaman and with that horrible omnadren I once had.

I did the exact thing with this Propionate I have. The only difference was in the morning when looking at the 2 layers, they were exact the same amounts´. If the water would have drawn the BA from the gear(oil) then there would have been more clear liquid and less gear than the night before.

I tried to mix 100mg(1ml) with EQ but still the same, maybe a little less pain but the swelling was there. The swelling occurs somethjing like 1 minute after injecting so It all goes very quick..

Therefor I assume this gear does not contain any BA but something else. Maybe as you wrote, they have used BB.

 

[ironmaster]

Good. I'll definitely try your method. I have just the thing to try it on, too. This shit cripples you, it has so much BA in it.......underground no-label crap.

 

[Skullfucked]

Benzl benzoate likely IS the problem. BB is commonly used in oil kits, fina kits, and by home labs to aid in suspending and preserving the solution. BB is some nasty shit......."for external use only, kills lice and scabies, should not be applied near open sores." It causes injection pain and flu like symptoms if present in high enough concentrations.
Tell me more about your technique for removing BA. I've never seen a consensus on how to do this. And I'd really like to know how to neutralize BB.......other than just buying euro gear.

Hold on. When someone shoots propionate why does everyone think it hurts? Too much BA to dissolve a short acting ester right? No. The pain is from the depot crashing inside the tissue. A proper amount of BB is not only a co-solvent but also will help the problem with depots crashing inside the tissue. I read it and tried it out for myself IT WORKS.
As per your comments about BB that is one thing it is used for. That doesn't qualify it as 'nasty shit'.

 

[MrRTTB]

so how would you remove the liqiud or whatever it is in there?

 

[MrRTTB]

BUMP!!!!!

shit this hurts! Injected 50mg(0.5cc) with 1cc painless EQ and heated the syring up for 10 minutes under hot water, then injected very very slowly and now I can't sit down.

 

[jboldman]

Goodpoint, and in fact bb is commonly used as a solvent in pharm grade parenterals. This is a common use! This is not nasty shit, it is the way it is done!

jb

Hold on. When someone shoots propionate why does everyone think it hurts? Too much BA to dissolve a short acting ester right? No. The pain is from the depot crashing inside the tissue. A proper amount of BB is not only a co-solvent but also will help the problem with depots crashing inside the tissue. I read it and tried it out for myself IT WORKS.
As per your comments about BB that is one thing it is used for. That doesn't qualify it as 'nasty shit'.

 

[ceo]

dont shoot prop

on a different note...how do you make suspension shots less painful???