High BA=PAINFULL injection?

[flyingfox272]

Started using a new lab for my test enan and I'm not digging the pain. The label reads 5% BA 10% BB @ 300mgs per ml.

The pain seems to peak the second or third day after the injection, I know the norm for BA is usually 2%, so is it possible the extra BA is the problem.

BTW,injecting quads and delts.

 

[trader]

Started using a new lab for my test enan and I'm not digging the pain. The label reads 5% BA 10% BB @ 300mgs per ml.

The pain seems to peak the second or third day after the injection, I know the norm for BA is usually 2%, so is it possible the extra BA is the problem.

BTW,injecting quads and delts.

Get some BA, inject yourself with .5 CC and see for yourself. Absolutely no pain . The hormone wasn't prepared right.

 

[flyingfox272]

Get some BA, inject yourself with .5 CC and see for yourself. Absolutely no pain . The hormone wasn't prepared right.

I actually gave a bottle to my buddy and he ran it with no complaints and good results, I have four more. The pain in my delt makes it hard to even lay on my side at night. I have done enough AAS in my day to know how it's supposed to feel, I
think I may just unload these.

 

[solidspine]

Bake it at 220 degrees for 30 minutes, be sure and place a needle in the vial so the stopper does not pop.

 

[Jhotsauce7]

Bake it at 220 degrees for 30 minutes, be sure and place a needle in the vial so the stopper does not pop.

Good advice, it may have become crystalized ... if so baking it will solve the problem..


Or it could be impurities in the oil, in this case purchase some sterile oil and dilude the injections 1:1.

 

[palehorse51]

Started using a new lab for my test enan and I'm not digging the pain. The label reads 5% BA 10% BB @ 300mgs per ml.

The pain seems to peak the second or third day after the injection, I know the norm for BA is usually 2%, so is it possible the extra BA is the problem.

BTW,injecting quads and delts.

Yes, the ba is high. I homebrewed some test e at 4%. it hurt after a day.(not terribly) i have found 3% ba to be the best. just dilute your test by adding some oil through a .22 whatman filter. if you think it is due to the test crystalizing (crashing) run the vial under hot hot tap water for a few minutes while swirling before withdrawing for inject. i am not a fan of baking because you can partially cook the oil or damage the hormone. although some swear by this.

 

[LiquidPhire]

I baked my gear after the pain , and it significantly reduced pain from daily injections. just my input.

 

[flyingfox272]

O.K. I guess I'll try baking it @220 for thirty minutes and I will see if this helps. BTW, the gear is fully suspended(did not crash).

Thanks for the input.

 

[palehorse51]

O.K. I guess I'll try baking it @220 for thirty minutes and I will see if this helps. BTW, the gear is fully suspended(did not crash).

Thanks for the input.

Yep, Ba too high.

 

[solidspine]

O.K. I guess I'll try baking it @220 for thirty minutes and I will see if this helps. BTW, the gear is fully suspended(did not crash).

Thanks for the input.

Can’t explain it, but when it hurts, and then you bake it, often that solves the problem

 

[flyingfox272]

Baking works! I decided to bake one bottle of Test to see if this would make it less painfull and it worked.
This is the first time I have had such painfull gear. Shot it Saturday and two days later no pain to speak of . Had to be the high B.A.

Once again the Bros at Elite come through!
Thanks

 

[macrophage69alpha]

BA and BB both cause pain.

high mg solutions are not the way to go, better to use larger injection volumes- glutes and quads (upper sites) can easily take 5ccs.

 

[P01NTBL4NK]

when i baked my shit fluid came out cuz I put the needle in the liquid but when I took the shit out the fluid lvl was still the same. I am pretty sure it gets rid of all the BA like that