Gotta Be An Easier Way?

[flexdaddyz71]

Did my first inj of tren/prop yesterday in the glute. Today the other glute. Only 1.5 with a 22g The problem is the the site from yesterday is frickin sore and I gotta do this everyday dang day. Alternating each check. I'm only used to inj maybe twice a wk max. Looks like the quad will be the next step. That still means every fifith day for each site for the next eight weeks. Is there a tip or trick for easing the soreness? Dang tren better be worth it. Comments please & be nice. Thanks!

 

[njmuscleguy]

Yah, it's definitely worth it IMO.

Learn how to poke your quads and shoulders... they're alot easier than you think. Use 23-25G, 1" for quads. Use 25G, 5/8" for shoulders. Now you have 6 sites to rotate.

 

[G.Sizzla]

Did my first inj of trenbolone/testosterone propionate yesterday in the glute. Today the other glute. Only 1.5 with a 22g The problem is the the site from yesterday is frickin sore and I gotta do this everyday dang day. Alternating each check. I'm only used to inj maybe twice a wk max. Looks like the quad will be the next step. That still means every fifith day for each site for the next eight weeks. Is there a tip or trick for easing the soreness? Dang trenbolone better be worth it. Comments please & be nice. Thanks!

Smaller gauge needle for sure!

 

[GUARDIAN]

heat up the oil

 

[flexdaddyz71]

Big8&20-

Can you explain how and why? Benifits?

 

[halfcenturian]

I shoot quads only. What has helped me is to warm up vial before shooting , then do some cardio or leg work. Anytime you start a cycle you will be sore for a few days. But after a week or so. You will be GTG. No easier way, bro.

 

[wzkid]

Also dont inject too close to the surface. The deeper I go it seems like the less pain. And the warming up the oil first works great.

 

[wzkid]

Here is a link for heating tips.

http://www.elitefitness.com/forum/steroids-discussion-forum/heating-pins-584998.html

 

[GUARDIAN]

Big8&20-

Can you explain how and why? Benifits?

I like to use a hair dryer simply for convienance.

If u preload your syringes I would heat up the barell evenly on all sides (medium heat setting will suffice). When the barell is warm to the touch it is good to go. This basically changes the viscosity of the oil (making it less thick).

If you dont preload then just heat the vial with the hair dryer (u could get away with higher heat setting bc on vials), draw & then inject. You could also make a very warm water bath in a shallow dish and put your vial in that for a couple of minutes.

 

[fireflyer]

I only do my quads and never do anything that has to be EOD or ED - screw that! Use longer esthers gear and have some PCT like Nolva on hand. Or be a pin cushion - whatever - your choice in the end. I agree with everyone saying warming helps. My favorite easy trick for that is to load the pin then put the needle cap back on. Holding it by the cap between thumb and forefinger spin it left and right under a hot water tap for 30-60 seconds. Careful to make sure none of the water goes under the cap. This is the fastest and easiest way I know and you're almost guarenteed to have access to hot water all the time.

 

[boletryne]

warm up the oil, use a smaller pin..it usually dont hurt as much after a few times.. gets used to it! just remember to inject slowly and massage it good after.

 

[HAYEZ]

eastiest and most convienent is buy sterile oil from any pin place and cut .5ml into each shot....then no more pain