EMM386 not installed ??? HELP

[thefantom1]

This is what I get when I load up Windows 98... EMM386 not installed..unable to set base frame address
Press any key to continue.. ok first what does the EMM386 do?? And how do I get it to load properly?? And I deleted the post about the HIMEM error........that was some confusion on my part.. HELP I'm pretty sure it's something I have to do with my config.sys here is my config sys.. and the himem is first like its supossed to be I don't get it..


DEVICE=C:\WINDOWS\HIMEM.SYS
DEVICE=C:\WINDOWS\EMM386.EXE
REM [Header]



REM [CD-ROM Drive]
REM DEVICE=C:\CDROM\ATAPI_CD.SYS /D:MSCD001 /PIO

REM [Miscellaneous]

REM [Display]

DEVICE=c:\windows\setver.exe
DEVICE=C:\WINDOWS\SYSTEM\METZKW.SYS
[common]
DEVICE=C:\CDROM1\CDTECH.SYS /D:MSCD001 /UDMA2 /V
LASTDRIVE=M

 

[thefantom1]

BUMP............

 

[Steroid_Virgin]

SYMPTOMS
When you boot your computer and EMM386.EXE loads (from the CONFIG.SYS file) you may receive the following message:

EMM386 Not Installed - Unable to set page frame base address



CAUSE
This message indicates that EMM386 was unable to find 64K of contiguous space needed for the expanded memory page frame.

When you specify the RAM switch (or no switch at all), EMM386 attempts to create a 64K page frame in the upper memory area (UMA). The actual amount of extended memory used will be 108K (64K + 44K = 108K). The extra 44K is used for tables that EMM386 sets up to emulate expanded memory.

This 64K of space acts as a window into expanded memory allowing programs to see all the available expanded memory 64K at a time.



RESOLUTION
If you receive the message noted above you can try the following:



Use the NOEMS switch if expanded memory service (EMS memory) is not needed.


Make sure HIMEM.SYS is installed above EMM386.EXE in the CONFIG.SYS file. Other devices should be loaded after EMM386.EXE.

NOTE: Some hardware configurations require certain device drivers be loaded before HIMEM.SYS. Specific examples are:


DMDRVR.BIN (disk manager)


EMM.SYS (expanded memory driver)


ADAPTEC.SYS (driver for Adaptec controllers)





If it is not an IBM machine, add the following parameters to the EMM386 command line in the CONFIG.SYS file:
device=c:\dos\emm386.exe i=e000-efff (m9 or frame=e000) ram
The E000-EFFF memory range is generally not used by non-IBM machines. Including this range can allow you to find 64K of free contiguous memory.


Specify different locations for the page frame to begin, using the "mx" switch, where x is in the range of the following table:
1---> C000 8---> DC00
2---> C400 9---> E000
3---> C800 10--> 8000
4---> CC00 11--> 8400
5---> D000 12--> 8800
6---> D400 13--> 8C00
7---> D800 14--> 9000
NOTE: Ranges 10-14 are for machines that have only 512K of conventional memory and the page frame is attempting to set below 640K.

For more information on EMM386.EXE switches, see page 606 of the User's Guide and Reference if you are using MS-DOS 5.0. If you are using MS-DOS 6, type "help emm386.exe" at the MS-DOS command prompt (without the quotation marks) and then press ENTER.


If the program requiring expanded memory can use the LIM 4.0 specification, then the 64K page frame can be set non-contiguously. To accomplish this, add the "Pn=address" parameter.

The following line in your CONFIG.SYS file sets the page frame by loading the four different pages in the indicated non-contiguous locations:
device=c:\dos\emm386.exe p0=c800 p1=d400 p2=e000 p3=d000 ram