Please Scroll Down to See Forums Below
CYP Powder
- Thread starter TEST APE
- Start date
L.D. 50
New member
TEST APE said:
hey bro. i don't usually frequent this site anymore, but my home at s*ology is down.
cyp is easy. just go with a 2%ba and 18%bb ratio and add your favorite oil.
for 200mg/ml you need 50 ml total less ~8ml for cyp weight, so 42 ml total for solvents.
2%ba= 1ml
18%bb= 9ml
oil= 32ml
powder~8ml
Mythicalbeing
New member
Here are the directions for 40ml of 250mg test cyp....
I disagree with the people above...too much ba/bb.
Test Enanthate 10 gram conversion
Needed
10 grams test E
2ml Benzyl Alcohol = 5% BA
30.5 ml sesame oil
Syringes 3cc & 5/10cc
18 or 20 gauge needles
mixing Vial
Sterile Vial
Whatman sterile filter
1. Weigh out 10 grams of powder.
2. Place powder in vial.
3. Add BA to the vial.
4. Heat oil in the oven to help sterilize it, heat to at least 212 degrees F. I usually heat my oil at 275 to be sure, I put the oil in a muffin pan, just fill one of the indentions this is plenty for these experiments. Also heat more oil than you need, as you will not be able to get it all out of the pan.
5. Add oil to the vial, save 2 ml of oil in the syringe for later. Gently shake vial.
6. Heat mixture if necessary. I like heating my powder products, by placing the vial in a frying pan, and placing it on the eye of the stove.
7. Place a 18 or 20 gauge needle in the sterile vial attach Whatman sterile filter.
8. Place another needle in the sterile vial to relieve the pressure.
9. Draw out solution with a syringe, run though Whatman filter.
10. Take other syringe with 2ml oil, run through Whatman into solution.
Makes 40ml @ 250mg/ml
I disagree with the people above...too much ba/bb.
Test Enanthate 10 gram conversion
Needed
10 grams test E
2ml Benzyl Alcohol = 5% BA
30.5 ml sesame oil
Syringes 3cc & 5/10cc
18 or 20 gauge needles
mixing Vial
Sterile Vial
Whatman sterile filter
1. Weigh out 10 grams of powder.
2. Place powder in vial.
3. Add BA to the vial.
4. Heat oil in the oven to help sterilize it, heat to at least 212 degrees F. I usually heat my oil at 275 to be sure, I put the oil in a muffin pan, just fill one of the indentions this is plenty for these experiments. Also heat more oil than you need, as you will not be able to get it all out of the pan.
5. Add oil to the vial, save 2 ml of oil in the syringe for later. Gently shake vial.
6. Heat mixture if necessary. I like heating my powder products, by placing the vial in a frying pan, and placing it on the eye of the stove.
7. Place a 18 or 20 gauge needle in the sterile vial attach Whatman sterile filter.
8. Place another needle in the sterile vial to relieve the pressure.
9. Draw out solution with a syringe, run though Whatman filter.
10. Take other syringe with 2ml oil, run through Whatman into solution.
Makes 40ml @ 250mg/ml
Mythical, you said we use too MUCH ba/bb, but your recipe calls for double the amount of BA I use. Only difference I can see is that you don't use BB, which I think helps as it thins out the solution and makes it easier to work with and inject. Besides, 2-3% BA is more than enough to sterilize, why use more, it just makes it more painful.
Mythicalbeing
New member
To keep the solution suspended..is the answer. Other wise in a matter of days crystals will form sometimes too small to see...ba will sterilze and suspend the powder in the oil. In my opinion bb is not needed in most cases.
Mythicalbeing
New member
Last thing....Benzyl alcohol has properties of strong polarity and limited water solubility and thus is used as a general solvent for inks and lacquers and a degreasing agent in cleaners. This compound is used as a photographic developer in the processing of color movie films and as a dyeing assistant for filament nylons. Its applications include many pharmaceutical preparations as a bacteriostatic. It was used for antipruritic activity to relieve itching.
Benzyl benzoate
It is widely used as a food preservative, normally as the sodium, potassium, or calcium salts and their derivatives especially in acid foods. Benzoate preservatives applications in foods, drugs and personal products are well established. It is also widely as an intermediate for chemicals, alkyd resins, polyesters, plasticizers, dyestuffs, preservatives, and rubber activators and retardants. Benzoic Acid is a diverting agent in crude oil recovery applications.
Benzyl benzoate
It is widely used as a food preservative, normally as the sodium, potassium, or calcium salts and their derivatives especially in acid foods. Benzoate preservatives applications in foods, drugs and personal products are well established. It is also widely as an intermediate for chemicals, alkyd resins, polyesters, plasticizers, dyestuffs, preservatives, and rubber activators and retardants. Benzoic Acid is a diverting agent in crude oil recovery applications.
Well, let's put it this way... I've made 500mg/ml ml eq and enth with only 1% BA, and it NEVER crystallized. So forget that. I will use more BA when using shorter esters like prop/acetate, or when mixing gears like cyp/enth or cyp/deca. Otherwise, I've never seen a need for 5% BA with just plain test enth at 250mg/ml. And the BB may not be needed, no, but it helps thin out the solution, which I like, b/c then I can inject all my painless gear through 29g slin pins 
Now, when I start throwing in BW, polysorbate80, and super-solvent to make tren base in water... now that's gonna be fun 
Now, when I start throwing in BW, polysorbate80, and super-solvent to make tren base in water... now that's gonna be fun
Mythicalbeing
New member
Lowest sounds like you and I enjoy dabbling in chemistry.
