Crushing fina pellets

[Stiffler]

When I usally make fina I just through the pellets in, but this time I think I want crush them to make it easier. can anybody share with me how u go about crushing them, so I dont make a mess?

THANKS

 

[Zyglamail]

if your using a kit, crushing them is a watse of time, just let them sit in magic soultion until they are dissolved.

 

[Stiffler]

yea im using a kit from syntholdirect, really u think it will work just as good if I dont crush them? hmm

 

[Hugh Gellatts]

just heat for a little on a range set on lowest setting. Much more sanitary than poking something into the vial to mash the things.

 

[bud 1]

fina

If you really want to crush them, buy a mortar and pestle...best way to crush them...or take a McDonald's straw or any other type....put somes fina "rocks" in it and crush them with a hammer or the above mentionned mortar.....hope this help....

 

[J.Luv]

Stiffler

You gotta let me know how the kit is from syntholdirect. I'm considering ordering from them.

-J

 

[Zyglamail]

I only use A kits and the magic dissolves the pellets just fine. I actually let mine sit overnight. Only down side is oxidization which doesnt hurt anything but can make the final product a tad darker. With A kits, not matter how long it sits in magic solution, coffee pre filtering is not needed.

 

[Stiffler]

so far J.Luv everything seems to be going great... hit me with a PM tomorrow and i'll tell u how the final product is.

 

[nikolai_bolkov]

The problem with crushing the pellets is that they stick to everything, so you lose some pellets along the way. Also, if the powder gets wet, it's a pain to wash it off. I have some fina stains on a black table that won't come off.

 

[rugger]

i tellin' ya

this is the best way to crush them, no stickiness. It even comes with a little brush to help sweep the finely crush fina.

Next time I make some, I post pics (not so big as this though, oops).

Rugger

 

[Stiffler]

NOWAY....LMAO

 

[The_Eviscerator]

I use a mortar and pestle.

 

[rugger]

YESWAY

A vet somewhere suggested it. He was just adding the fina to oil and injecting, so I definitely see his concern with dissolving completely.

Well, my buddy kust use the kit whileI use good ole Mr C. He was not the happier camper.

What does a motar and pestle cost you?

Rugger

 

[bud 1]

Approx. $12 for a mortar and pestle made out of ceramic...

 

[Suspension]

I bought a pill crusher at a local nutri. store. it cost about $5 and it can crush a bunch of pellets each time...it worked out nicely.

 

[Manilla Gorilla]

Pill crusher from GNC. About $7, no mess
Later

 

[Intramuscular]

When you order your kit, buy a glass stiring rod. I think it's only like a dollor or something. Use it to crush the pellets in the solution.

 

[FriarFuckk]

just heat for a little on a range set on lowest setting. Much more sanitary than poking something into the vial to mash the things.

I agree with hugh, I let the pellets sit in the solution for about 1 1/2 hour and then drop the vial into boiling water to further speed up the process, then I just fish them out with tongs and begin the filtering.......

 

[Stiffler]

I just said screw it and went with the same way I always do it just through the little buggers in there and wathed them disolve. this time though it only took about 35mintues I was shoked usally it takes almost an hour for them to disolve.

well its all filtered and ready to go

 

[rugger]

Mr C

$9 and 5 seconds and my fina is a fine-no-mess powder that dissolves in a couple of minutes.

Later
Rugger

 

[AnabolicDiabetic]

Use two spoons...put pills into one spoon the press the back of the other spoon into the other and crush and grind. Makes a very fine powder.