Please Scroll Down to See Forums Below 
finafiend1
New member
I got this from an old post. If it works, it'll only cost about $15 to make 100ml of 75mg/ml tren. A's kit is $60. It's a quarter the cost, not that much more work and best of all, A sells all the ingredients. Does this sound like a good recipe. I'm hoping to hear from Andy especially.
------------------------------------------------------------------------------------
Many athletes utilize a slightly more complex method of formulating an injectable that solves the problems created by simply mixing the crushed pellets in the method described above. By mixing the crushed pellets with propylene glycol, benzyl alcohol, and polyethylene glycol, it's possible to create a much more effective injectable that is resistant to microbial contamination.
The following materials are required to complete this experiment:
-trenbolone acetate
-propylene glycol
-benzyl alcohol
-polyethylene glycol
-syringe filters
The polyethylene glycol (PEG), propylene glycol (PPG), and benzyl alcohol (BA) should comprise 60, 30, and 10% of the final mixture respectively. Therefore, if it was your intention of producing 100 ml of injectable, you would need 60 ml of PEG, 30 ml of PPG, and 10 ml of BA. For 50 ml, you would use 30, 15, and 5. The final concentration of trenbolone in your injectable is determined by how dividing the total mg of amount of trenbolone by the total ml volume of the solution. For example, if you desired to make 50 ml of injectable with a final concentration of 50mg/ml, you would need to start with 2500 mg of the steroid.
The procedure is as follows:
1.The required amounts of PPG and BA should be mixed together.
2.The required amount of steroid should be added to the solution while it is heated. It's best to immerse a sterile container containing the solution and pellets into hot water so that the temperature can of the mixture can be carefully controlled. Care should be taken not to allow the solution to become too hot.
3.After the steroid has dissolved completely into the PPG/BA solution, add the PEG and mix the solution until it is evenly distributed.
4. Draw the solution up in a syringe and pass is through the syringe filter into a sterile container. This will remove any particulates that may be present and help sterilize the solution.
5.As an optional step, some athletes will initially dissolve the pellets in acetone. The resultant solution is then poured through several coffee filter, catching the glues and binders. The end solution should be left to evaporate until you are left with pure trenbolone crystals.
The third and final method of producing an injectable is to purchase an experimental kit designed for that purpose. The advantages of purchasing a kit is that all of the materials necessary for the experiment are provided for you at very little expense. One very popular kit is profiled later in this article.
------------------------------------------------------------------------------------
Many athletes utilize a slightly more complex method of formulating an injectable that solves the problems created by simply mixing the crushed pellets in the method described above. By mixing the crushed pellets with propylene glycol, benzyl alcohol, and polyethylene glycol, it's possible to create a much more effective injectable that is resistant to microbial contamination.
The following materials are required to complete this experiment:
-trenbolone acetate
-propylene glycol
-benzyl alcohol
-polyethylene glycol
-syringe filters
The polyethylene glycol (PEG), propylene glycol (PPG), and benzyl alcohol (BA) should comprise 60, 30, and 10% of the final mixture respectively. Therefore, if it was your intention of producing 100 ml of injectable, you would need 60 ml of PEG, 30 ml of PPG, and 10 ml of BA. For 50 ml, you would use 30, 15, and 5. The final concentration of trenbolone in your injectable is determined by how dividing the total mg of amount of trenbolone by the total ml volume of the solution. For example, if you desired to make 50 ml of injectable with a final concentration of 50mg/ml, you would need to start with 2500 mg of the steroid.
The procedure is as follows:
1.The required amounts of PPG and BA should be mixed together.
2.The required amount of steroid should be added to the solution while it is heated. It's best to immerse a sterile container containing the solution and pellets into hot water so that the temperature can of the mixture can be carefully controlled. Care should be taken not to allow the solution to become too hot.
3.After the steroid has dissolved completely into the PPG/BA solution, add the PEG and mix the solution until it is evenly distributed.
4. Draw the solution up in a syringe and pass is through the syringe filter into a sterile container. This will remove any particulates that may be present and help sterilize the solution.
5.As an optional step, some athletes will initially dissolve the pellets in acetone. The resultant solution is then poured through several coffee filter, catching the glues and binders. The end solution should be left to evaporate until you are left with pure trenbolone crystals.
The third and final method of producing an injectable is to purchase an experimental kit designed for that purpose. The advantages of purchasing a kit is that all of the materials necessary for the experiment are provided for you at very little expense. One very popular kit is profiled later in this article.
