Please Scroll Down to See Forums Below 
An alternative to A A P's "Painless Injections Everytime"
Sorry bro, i had to post this. Forgive me!
These are my tips, and they don't involve any icy-hot cream (fag reference) that someone claims penetrates the muscle when it's rubbed in- BTW it doesn't! It simply brings blood to the area affected by the active ingredient... This is for beginners and novices alike, though i'm sure after the first few injection most of you gear heads figured all of this out.
P.S. these tips work very well for Fina and were made specifically with it in mind.
1. go with a higher per gram kit. (BA content is "approx" the same for all kits, hence slightly more painful with the smaller kits)More oil equals less pain.
2. Use a high gauge needle (25g) there’re very smooth going in and no visible outward sign of injection should be present.
3. Warm your gear up before you load your syringe (run it under HOT bath water until the vile and the oil is about 110 degrees) By the time you inject it should be just above or close to body temperature.
5. Inject very slowly (should take 30 or more seconds to inject 1ml- the faster you go=the more painful it will become)
4. Once you remove the needle from your skin, apply lots pressure and massage the area extensively! (this is very important, because it helps disperses the oil throughout the muscle which equals less of the "knotting" feeling)
5. work out a muscle then inject it, not reverse. Some guys like to inject and then workout, i cannot tell you how they do it- I just know that i cannot hit a muscle 100% after sticking a 1 inch piece of steel into it and forcing 1ml (or more) of oil into it! (i tried it once, so let my stupidity be your wisdom)
There are other tips (like shower before/icy-hot masturbating cream on site of injection) but you probably know them and there not as useful as these IMO, hope this helps. And if you have any questions about the techniques not mentioned (like the flex-sol 454 method, with your pants around your ankles) ask the icy-hot master himself, Alien Amp Pharm!
Sorry bro, i had to post this. Forgive me!
These are my tips, and they don't involve any icy-hot cream (fag reference) that someone claims penetrates the muscle when it's rubbed in- BTW it doesn't! It simply brings blood to the area affected by the active ingredient... This is for beginners and novices alike, though i'm sure after the first few injection most of you gear heads figured all of this out.
P.S. these tips work very well for Fina and were made specifically with it in mind.
1. go with a higher per gram kit. (BA content is "approx" the same for all kits, hence slightly more painful with the smaller kits)More oil equals less pain.
2. Use a high gauge needle (25g) there’re very smooth going in and no visible outward sign of injection should be present.
3. Warm your gear up before you load your syringe (run it under HOT bath water until the vile and the oil is about 110 degrees) By the time you inject it should be just above or close to body temperature.
5. Inject very slowly (should take 30 or more seconds to inject 1ml- the faster you go=the more painful it will become)
4. Once you remove the needle from your skin, apply lots pressure and massage the area extensively! (this is very important, because it helps disperses the oil throughout the muscle which equals less of the "knotting" feeling)
5. work out a muscle then inject it, not reverse. Some guys like to inject and then workout, i cannot tell you how they do it- I just know that i cannot hit a muscle 100% after sticking a 1 inch piece of steel into it and forcing 1ml (or more) of oil into it! (i tried it once, so let my stupidity be your wisdom)
There are other tips (like shower before/icy-hot masturbating cream on site of injection) but you probably know them and there not as useful as these IMO, hope this helps. And if you have any questions about the techniques not mentioned (like the flex-sol 454 method, with your pants around your ankles) ask the icy-hot master himself, Alien Amp Pharm!
Last edited:
