Step By Step Guide For Homebrewing

[MasonicBodybuilder]

Head over to evolutionary.org There is a great brewing thread there should you have any other questions.

 

[Sylvis29]

Ok I know this thread is old, but I tried this brew doubling everything since I had exactly 50 g of powder. I should have come out with 200 mls I instead came out with about 240. Anyone have ANY idea why?? Yes I did the math on doubling correctly.

 

[Twenty4/7]

Dang

 

[gabrielblauth]

My friends, quick question: once I'll use the vacuum pump, I still need to use the coffee filter to pre-filter or I'll be able to go straight to the vacuum pump? THank you!!

 

[SteveMobsterG]

Same as before - go to the home brewing thread mentioned above.

 

[stevesmi]

wow blast from the past

 

[MasonicBodybuilder]

^^^^Yea, this thread has been pretty quite for a while now.

 

[muskate]

Check out the home brewers thread on evolutionary.org -> https://www.evolutionary.org/forums/source-talk/homebrewers-lounge-part-2-a-34895.html

 

[Dunamis Marine]

Alright guys I decided to make this guide so that people would literally have no questions on homebrewing.

In this guide I will be brewing Testosterone Enanthate. I made 10 bottles each dosed at 250mg/ml. Alright lets get started the pictures will do alot of the talking.

Supplies:
Scale (Get one that is sensitive enough to the gram)
Vaccum pump(Brake Bleeder)
250ml Nalgene/Millipore Filter(I like Millipore better but did use a Nalgene. You can use a whatman but that takes to long for me)
25grams of Testosterone Enanthate powder
18ml of Benzyl Benzoate (BB) (USP)
2ml of Benzyl Alcohol (BA) (USP)
61.25ml of Grapeseed oil
3ml syringe with 18-21 gauge needle
20ml syringe with 18-21 gauge needle
Small piece of paper
500ml beaker
100ml beaker
10 10ml vials
10 rubber stoppers
10 flip caps
Crimper

This is way more than 25grams but i'll show how to measure out. Sounds simple but its kinda tricky.

All right lets begin

First you weigh out your powder. Now you have to do this very carefully. get your small piece of paper and place it on the scale then press tare to set it to zero so it doesnt weigh the paper. Then slowly add your powder. Now here is the tricky part the powder weighs so little that the scale needs to be reset every time you add some. All you have to do is add some then press on the scale with your finger and let the number fall back down. Once you get 25 grams your good to go.

Then dump it into your beaker.

Add 2ml of Benzyl Alcohol (BA) (USP)

Then add 18ml of Benzyl Benzoate BB) (USP)

Next step is sort of optional but its makes things easier. Get a pot with a bout an inch of water in it and place it on the stove and set the eye to 3.

Put the beaker in it.

Watch the powder dissolve and the mixture get pretty close to clear.

Next add you grapseed oil and let it all warm up for a bit to make filtering a little bit faster. This is a pic right after I added the oil. In put it back on the eye for a minute and mixed it.

Then get your filter which comes with a cap for the bottom collection part.

Next pour the oil in and attach the vacuum pump and set it between 300-400. THIS IS THE SAFETY ZONE. DONT PUSH YOUR LUCK THE BOTTOM PLASTIC CONTAINER WILL CRACK.

Filtering (The flash on the camera makes the oil look kinda hazy)

Done the whole filtering process takes about 30 minutes but all you have to do is pump and walk away.

Next you measure out 10ml in each vial

I put the rubber stopper and flip tops on them but didnt crimp them yet.
Then you crimp.

And now your done. You have now made 100ml of Test E and put in 10 10ml vials. If you have questions pm me.

first thanks for the post.
Question from the tyro..
I have made Testosterone Cypionate 250mg/ml from 10 gr powder/ 30.5ml GSO / 3% BA / 15% BB and cooked with a phama grade hot plate and magnetic stirrer to a temp of 212 degrees for 30 minutes to liquid. Then filtered and capped. However: All my vials crashed by the next day. I can regain them with hot water, but I don’t want to heat every time I need to pin. I was told I could add Ethyl Oleate (EO) to avoid my cook from crashing. Just reaching out to you since you posted a great guide. Any ideas “welcomed” Thanx-Jim

 

[Dunamis Marine]

Question from a tyro.. I have made Testosterone Cypionate 250mg/ml from 10 gr powder/ 30.5ml GSO / 3% BA / 15% BB and cooked with a phama grade hot plate and magnetic stirrer to a temp of 212 degrees for 30 minutes to liquid. Then filtered and capped. However: All my vials crashed by the next day. I can regain them with hot water, but I don’t want to heat every time I need to pin. I was told I could add Ethyl Oleate (EO) in addition with the recipe to avoid my cook from crashing in the future. Just reaching out to you since you posted a great guide. Any ideas on that? “welcomed” Thanx-Jim